I had a chance to sit in a Eureka! High back recently and plan to buy one when the Canadian weather improves. It packs up to a similar size as all of these folding chairs and is of comparable weight. I plan on enjoying it while my wife sets up the mattress and sleeping bags in the tent - then...
I‘ve done some travelling in an NAS soft-top and Series III 88” - often as a solo vehicle. I started back in the early 1990’s when the available equipment was essentially backpacking gear in action packer boxes. Based on this experience - I agree with some previous posters that suggested you...
Wow - I dreamed of building one of these out in University. I was travelling in my Series III at the time, so noise level, driving discomfort etc, would have been a pretty even swap, Love the utilitarian practicality of this one.
Lack of experience - especially working on trucks that get used off-road - I find is often the difference between “looks nice and tidy” and considering what’s going to happen during 4 hours of washboard road.
I consider one of the primary benefits of doing the work myself to be the reduced...
Thank you to everyone who responded - I did contact Trevor at RovahFarm.
Despite being on vacation, Trevor traded phone calls, emails and texts with me for two days. Trevor confirmed the parts I needed, located them and shipped them quickly at a very generous rate. I can not speak highly enough...
Does Rovahfarm have a repair facility? My route south takes me right through Arkansas... I am thinking of saving the shipping to Canada and having it done on site.
Napalam00 - are you sure they have the parts onsite? I am leaving Sunday and won’t be able to contact them until I am south of the...
I am trying to identify the fuel tank in my 1984 110 station wagon, tdi; it’s a bit of a parts bin.
The tank pick up and sender is mounted on the drivers side (LHD) around mid-tank. The top is sealed. The return line feeds into a metal elbow protruding from half way up the tank and roughly 1/4...
Anybody know the modern part# equivalent for the brake pads? I keep coming up with STC3765 or RTC5756. My parts source indicates these have been superceded but don’t provide the new part#...
Am I right to assume LR017951 will suit any non-vented from caliper?
Thanks again...
Thank you for the replies... I am confident in the RTC3380 determination. I was able to cross-reference the Lockheed part#.
I have included a photo - I have an oil leak to sort...
Thanks again...
I need to address an intermittent clicking noise from a rear brake on my 110. The caliper on this Salisbury disc conversion appears to be working fine, but I assume there is an issue with the anti-rattle springs or the disc/pads are worn.
The caliper is stamped - Lockheed 3247-637C - which I...
Have you had a few cold/warm weather cycles with snowfall? I had a similar “strained crank” issue with my tdi a few winters ago. While I searched for answers I tented the rear and put a camp stove under the diesel tank to deal with possible gelling.
I turned the engine over about an hour later...
I use my 110 in a similar manner - daily driver with laden family camping trips. With the winch/bar, 300 tdi upfront I will be sticking with the OME Medium for my next suspension.
In the rear, I am leaning towards the air lift helper springs inside a lighter duty coil. I have no experience...
I ordered the Exmoor kit - https://www.exmoortrim.co.uk/our-models/defender/defender-110/defender-110-pre-2000/second-row-seating/seat-belts/4-point-inertia.html - it did come as a set and does retract fully in my ‘84 110.
I think the part number for the female half is BTR4373 - but I agree...
I am deep into a number of ?while I have that in pieces? jobs on my Defender. I just installed an X-brake. The directions detail a course adjustment to deal with the varying lengths of available cables.
It appears X-Eng have replaced the nut and locking tab with a torx fastener. I assume the...
I have an ‘84 110 and ordered the same brackets from lrdirect. Both required drilling to clear various fasteners.
The research I did at the time indicated it was required on earlier trucks.
Henry
I removed my 300tdi radiator today as part of a timing belt refresh. I noticed corrosion on approx. 75% of the rear fins - in fact a number flaked off with very little provocation. The rods appear ok with no leaks, but I think after 10 winters it may be time for a new rad. Clear rust along the...
Thank you for the suggestion - I did see a YouTube video of that tool in action.
I am due for a timing belt next spring and have some Rover travel plans that summer. I have assembled a wife infuriating pile of parts to install in the next few weeks -a timing belt is one of them...
Henry
Thanks for all the replies and suggestions.
I did order a Bosch reman from LrSeries; it will allow me to quickly turn around the repairs.
It’s going to be a long weekend...
Henry
Thanks for all the replies...
I did contact LRseries regarding their Bosch units. They did reply that the injector pump they have for sale is a Bosch factory reman with a 24 month warranty. At almost half the price of a new injector pump I am tempted. This would get me back on the road quick as...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.