To set the stage, 85 ROW LR110 CSW with 60/40 bench in second row.
Would like to upgrade to a left and right side single seat, hi back, that teenagers can actually sit in.
have looked at the RN upgrades and the Exmoor trim upgrade - like but want to run any other options folks have used.
Q1: Do...
On my 85 LR110, tackling the rear clunk.
Salisbury rear end.
Have looked at a frame and don’t think that’s is it.
Next.
Pulling hub flanges and axle shafts to inspect condition of splines.
Also pulling rear diff to inspect and test off vehicle, to determine if slop is hub-spline or axle-diff...
Looking at upgrading my original seats and am considering either exmoor trim premium or puma seats, but would like to at least sit in one or the other before pulling the trigger,
Is there anyone in eastern NC with either the Exmoor Premium seats or Puma defender seats, or any other upgrade...
LR110, 300 tdi with R380, Salisbury rear end. Running 235/85R16 size tires.
Makes a thunk from rear end when releasing clutch periodically, also when I ease off accelerator pedal and then press down again. I have read the threads on that god awful defender clunk.
Feel a inch or 2 of play in...
This evening, got a steady, then flashing battery indicator light and voltmeter showed no charging, hovering at +12v rather than higher when normally running.
No issues noted yesterday when driving.
First going to check alternator output, then check all wires.
Any other suggestions?
Engine...
Question. Will 98 Disco front seats fit into 85 ROW LR110 with similar mounts, etc? Do they have the removable base? Have no discovery experience, but may have a line on some front seats, if they are compatible. Presently sight unseen.
Advice/input will shape next move.
Thanks
Mark
For a 300tdi, has anyone installed a low coolant alarm. Was reading about the Engine Saver device, looks good, seems limited to those in Oz.
http://enginesaver.com.au/
Also saw the DaviesCraig variants on jegs. https://www.jegs.com/i/Davies-Craig/317/DC-1035/10002/-1
Like the screw in...
Replacing my leaking P gasket. Recommendations for what kind of ?form-gasket?to use with metal gasket. Should it be rigid or semi drying stuff? Have some permatex blue and red. Did it before with no sealant and it failed soon after.
Thanks
I finally got a planar diesel air heater to warm up the drafty cab.
Any advice on where to tap for fuel. Was thinking about putting a T fitting in the return line, but wanted to check before cutting anything.
Thanks
300 tdi if it?s important.
Working to install (right) my new VDO speedo and need the 3 wire plug that plugs into the Hall effect sensor, part Stc4637. NAS rear brake light plug.
I got one previously from Pedro and have lost it in my disaster of a garage.
Anyone have extra one lying about they could part with?
Thanks...
Noticed today that my left turn signal is misbehaving.
When I push the turn signal for left turn, all 4 signals flash, like with hazard. I heard flasher relay clicking. No indicator idiot light flashing on dash. Switch to right turn, only right signals, flasher relays clicks normally, idiot...
I don't know the brand of Ac system, but I have an aftermarket Ac in my Rhd 300tdi that needs a r134 recharge. Anyone have an idea about how much a comparable 300tdi Ac system holds,
Ok, noticed coolant leaking past expansion tank cap .
Opened and it was full to top. Started up, ran until temp above 188, fan came on, lower rad hose hot, top rad hose cool to touch. Cool fluid still coming out of expansion tank.
Temp keeps rising .
300tdi Land Rover 110.
Revotec electric...
Coming back to finish the project.
300tdi.
Backstory: Replaced o ring in FIP as it was leaking. Done.
Installed a new sedimentor and 12v fuel pump, per recommendation of the distinguished mr davis. Done.
Pump comes on with ignition and is pumping. Not started, just ignition on. Bled air...
Need some guidance.
300tdi
Fuel sys bleeding.
I removed the FiP to replace the oring, used all special tools to lock flywheel, secure timing gear, so nothing moved.
O ring replacement went fine, per dieselgeekwrite up.
Ready to prime and start.
I have hand primed for a while, with nothing...
Am preparing to remove my FIP to install new seal. Have the special tools to lock the flywheel at tdc and secure the timing gear.
Having reviewed all the trailfitters videos with one question.
How do you advance the flywheel around to the notch with the engine installed. The vids all use a...
Facing a leaky injector pump on my 300 tdi. Looks to be the o ring. I have the parts from tdi guys - viton o ring, caps and special bolt to keep it all together.
I have reviewed the posts and videos from tdi guys as well.
Any advice or lessons before I dive in. I know it can be much bigger...
Truck is ROW 1985 LR110 with Wipac Led lights all around.
Installing a trailer wiring harness.
Does anyone know if there are issues splicing in the turn indicator wiring with LED lights? I can't imagine there would be, but figured I would ask before rather than ask when I have jacked up my...
Howdy
Just discovered a small puddle of diesel under the truck and a wet underside/rear on my injector pump. Pipe connections seem dry.
I have ordered the viton o ring kit and with some good write ups, will get after it.
Question.
Any issues or problems that can arise if I keep driving it...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.