Search results

I’m moving and need to find new homes for these. 19J motor out of 89 D90,120k miles. Ran when removed and smoked a lot. New injectors, injector lines, timing belt, water pump, clutch. Attached to it is a good LT77 s/n 51AD3259E and LT230 s/n 28D2496693F ratio 1.222. In a box is a LT77 s/n...

If you were following my rebuild project you saw that everything was going great until I drove the rig. It appears the transmission 2nd gear syncros are out and the mainshaft splines are done. So im looking at ordering a transmission and transfer box from Ashcroft. Any other suggestions? When...

Along with a other gauges I installed a new VDO electronic Speedo p/n 437-151. Well it won't work. First thing, the install instructions say that when the indicator is first powered up it does a self test and the gauge needle will sweep across the whole range. That doesn't happen. When the...

Im looking for a radiator fan shroud for my 2.5Td to 200TDi conversion. Is the 200TDi fan shroud the same as the 300TDi? Thanks.

I have a VDO Pyrometer gauge on order but is backordered. I have the exhaust manifold off and wanted to drill and tap the probe hole while its off. The gauge is backordered for an undermined time and I would like to go ahead drill, tap an plug the hole so I can continue the motor reassembly...

What RTV is used on the oil sump and ladder frame? While I have the motor out I'm replacing all the possible seals. I just removed the oil pump and ladder frame and saw that a type of RVT was used not a gasket. Any suggestion on what to use when it goes back together? Thanks. This is on a 200TDi

During the month of February and likely into March I will be doing a re-power of my 1989 D90. It currently has a J19 motor and Ill be upgrading it to a 200TDi and doing a few other things along the way. The memorial part is that it was my wife and I desires to do some overloading and offloading...

I have two Overland aid kits available. I have a small business making customer specific first aid kits and providing training. I have put together two overland kits that I think fit the needs of most off-roaders. These kits are not designed to be all inclusive, they contain 'must have' items...

Im looking for a good used LR3. 2007-2009, black interior, silver, gray or black exterior, SE, V8 model and a west coast vehicle. The ideal truck would be well maintained, low milage and reasonably priced. If you know of one hit me up please.

Is there a better way to get fuel out of a jerry can? I have some old school jerry cans that I carry with me during hunting season due to the small 15 gal fuel tank on my D90. I have the flexible steel nozzle that screws into the can, again old school. The problem is that it takes an agonizingly...

Im wanting to repaint the wheel arches and am wondering if the plastic rivets that hold the arches on can be reused or need to be cut off and replaced? Thanks for you input.

Pretty excited, picked up a Warn Model 8274 today for $200. Been watching for one of these to pop up for a while. Any suggestions for a bumper and what if any I should do for the electrical system.

Taking Landy on her first road trip Thursday. I have to go to Wenatchee Washington for some training and thought I would try driving the Rover over. Its about a 230 mile one way trip. Wish me luck. First time out of town with the rig. I have had it since Aug of last year and since then...

Looking for a fuel tank. I have a 1989 Defender 90 ROW, 2.5L TD. My tank stated slowly leaking last month. I wasn't to concerned about it, wanted to wait till better weather to pull it. Well a few days a go I noticed fuel leaking out of the garage and into the driveway, the tank decided it...

I am new to the Land Rover owners adventure and am wondering about quality of aftermarket parts. Im getting the impression that Britpart is a budget, lower quality part. Am I correct? What about Bearmach? Any other makers, other than Land Rover? Maybe someone with some aftermarket experience...

I have replaced the injectors in my new to me D90, 19J 2.5TD motor. I have one injector that is leaking fuel and it appears to be leaking from the bore in the head that the injector fits into. I have replaced the combustion seal and the copper ring twice and still leaking. I see in the parts...

Hello all, Im going to replace the timing belt on my 1989 D90 19J 2.5 TD ROW. Looking for advise on what manual or alternative source to use. Any suggestions on manuals or a PDF download location would be helpful. Thanks.

What is the correct valve adjustment clearance for a 19J motor? Searching the web I got .20mm, .25mm and .5mm. Anyone know for sure? Is this a cold adjustment? Much appreciate the help. Thanks, PB