Search results

Is there a seal between the master cylinder and the servo? Asking for a leaking friend as seen in the photo. Do I need to replace multiple parts here? And my brakes are soft. Even by 1983 110 standards…

83 d110, 300tdi Lights work, turn signals work, just not horn. That has me assuming it is not the switch. How do I check power at the actual horn- when I hook a multimeter up too the purple and black wires there I don't have power. Then I was wondering if that is normal- doesn't matter if...

I need to remove the rear step bumper and have all but the four bolts underneath/behind the hitch. Any tricks or ideas? It’s actually not super rusty I think they were just really cranked on there and it’s a tight area to get to. And for the rear crossmember my plan is to grind/clean away the...

New, never installed. As photographed. Asking $400 OBO + shipping from Steamboat Springs CO, 80487

Rebuilt around 2010 and installed in a 300tdi conversion. Replaced with a different ratio around 2018, guessing about 8k miles on it at the time. I hoarded it in storage until now, just in case I changed my mind. No issues prior to removal. $800 OBO + shipping from Steamboat Springs, CO 80487...

Used. Took it off b/c I wanted to upgrade. No issues with it before removing it. Includes turbo and manifold as pictured. Asking $500 OBO. Located in Steamboat Springs, CO 80487. Willing to ship at your cost.

I have a SD cage I am removing this week-end. This will include all of the parts except the brackets under the body. This includes all the exterior bars and the 1 interior hoop that mounts through the roof and hardware in the condition it is removed in. The cage is in decent condition- it has...

I have the Rovetec electric fan conversion and I am trying to decide if I want to install it or not. Truck is a 1983 110 300tdi, currently has the stock fan, uprated RN radiator, alisport uprated VGT turbo, slightly tuned IP with a boost pin. It's running well. What are the pros to installing this?

Set of 4 wheel spacers. Was going to fit alloy wheels on an 83 D110 and decided not to. Asking $80 + shipping for the set.

5 wheels off a 95 D90, nice condition. Have some scratches, and are dirty from sitting. Includes lugs. Asking $400 + shipping, located in 80487.

Retrimmed seat in Black Rack XS. Includes mounting hardware and floor portion of seat belt. Asking $500 + shipping

My 2016 LR4 AC has stopped working. Blows hot air. Local shop has quoted $2k to replace the compressor. Apparently the compressor is $1k. My first question, is there an aftermarket compressor I can use? And is it really $1k in labor? Thanks, Alex

I have a brand new- but not in the box FRO Slimline II 1/2 rack for a 110 or 130, probably fits a 90 as well. It is designed to mount to the gutter. New is $1429. Asking 700 OBO, buyer pays shipping from 80487...

My Webasto has locked up. I have the procedure to unlock it and reset it. I would like to be able to read the code and find out why it did this. The code reader is $600. Anyone have another way to do it without buying that? Is there a timer/display that would tell me the code?I think one of...

So…I have a Webasto coolant heater that has been installed, removed, and now installed again. Currently I am trying to finish the wiring. I have a new harness to replace the previous one that was “modified” to have a remote start. On the harness I have the following: - a red and brown wire that...

Looking for a set of installation plates that come with the SD exterior cage- the cage that is on the NAS 110. Need 4 for the rear tub and 2 for the front fender. Pic is from JimC

Used Tickford Top, modified for belt rails. I bought it use and never installed it. Has some stains as seen in pics. Includes the side pieces with snaps above the door. Asking 1500 + shipping

I have a 1983 110 with a Salisbury with drum brakes. I am assuming that it is stock. What is the standard gearing of that axle? I’ve read 4.1 and 4.7. Thanks, Alex

I am looking into changing the configuration of my 110 and that might be removing the NAS style roll cage. What are some thoughts on what to do with the holes in the body? I like the patina of my 110 so I don't want to start replacing panels and I am thinking I will probably leave the feet from...

I need to remove the tube side steps from the 90. The front is attached with the bulkhead bolt. I can get the nut of the bolt but I can’t get the bolt to move. I have sliders too (I know having both looks ridiculous) and the step attachment portion is sandwiched between the outrigger and the...