Search results

  1. jymmiejamz

    1991 200TDI to R2.8--couple remaining questions

    Ah okay, I thought they looked like something laser cut, so I was curious how you did that.
  2. jymmiejamz

    1991 200TDI to R2.8--couple remaining questions

    Did you make your own motor mounts?
  3. jymmiejamz

    14CUX Fuel Relays

    I’ve been using the AB ones for years and have installed several sets with no issues.
  4. jymmiejamz

    Used set of Eyebrows/Flares

    Have these been painted?
  5. jymmiejamz

    Oil Pan Clearance - TC and Drive Plate

    There is enough space, but I would recommend leaving it off because the torque converter bolts are hard to install with the pan in place.
  6. jymmiejamz

    NAS 3.9 Fan Clutch Removal - which direction?

    If the belt goes over the pulley, the fan is left hand thread. If the belt goes under the pulley, the fan is standard thread. You want to turn that one as if you were tightening a bolt because it is left hand thread.
  7. jymmiejamz

    car trailer

    Mine is pretty old and is totally the wrong spec. I think a z71 has lower gears in the diffs, they had optional air helper springs in the rear, Also could have got the 2500. The four speed transmission isn’t a good fit for it
  8. jymmiejamz

    car trailer

    It still is way underpowered, over geared, and the hydro boost brakes are garbage. I can’t wait to sell it haha
  9. jymmiejamz

    car trailer

    I tow with my 2005 suburban 1500 a lot, and it is a terrible tow vehicle. Mine doesn’t have the rear air suspension, so it really can’t handle any tongue weight. I have to use a weight distribution hitch for it to have enough tongue weight but not squat. It can be scary to to with compared to a...
  10. jymmiejamz

    car trailer

    Just my $.02, but used trailers often aren’t much cheaper than new ones. Trailers often tend to get abused. I’d consider new. I bought mine from Kaufman and have been very happy with it.
  11. jymmiejamz

    Cummins Repower ISF 2.8 for Defenders

    Is there a lot of difference in quality of AN lines? I don’t have a ton of experience with them, but i don’t like the way they look. I do appreciate how easy they are to use in custom applications.
  12. jymmiejamz

    Which doors fit which years? Which are the best?

    Is it a soft top or hard top? Either style will fit.
  13. jymmiejamz

    Land Rovers That Suck

    Way down yonder on the chattahoochee… I can only assume this build had an unlimited budget.
  14. jymmiejamz

    Land Rovers That Suck

    Finger over the lens is the cherry on top.
  15. jymmiejamz

    WTB - ~2006 Maserati Gransport

    Why a Gransport? I would be looking for a Granturismo, they are a much better car.
  16. jymmiejamz

    Source for blade style fuse box PRC4826

    I just used the standard non locking spades. There is a good amount of room back there for the harness with this fuse box. I just installed them today in a customer’s 110
  17. jymmiejamz

    LR4 Stuck in Park

    If you want a car to keep for a long time, the LR3/4 platform would not be at the top of my list
  18. jymmiejamz

    Source for blade style fuse box PRC4826

    No. On the back side of this panel there are male spades. I am going to use female spades I buy from Belmetric that are really thick like factory ones. You definitely need a ratcheting crimper for these ones
  19. jymmiejamz

    Source for blade style fuse box PRC4826

    I specifically wanted the wires to come in from the back on this. There are tons of options with side terminals though
Top